Coltene Coltolux Led Light Cure

Features
High output LED for fast cures. Cures 2 mm in only 10 s.
Dome shaped lens minimizes light diffusion.
LED light output matches the absorption spectrum of Camphorquinone (CQ) Photoinitiators.
Audible signal every 10 s and automatic power saving sleep mode after 20 s of operation.
Hundreds of 10-s cures with a fully charged power cell.

Description
The Coltolux  LED combines a slim curing probe with high output in a cordless lightweight penstyle design.

High output LED for fast cures. Cures 2 mm in only 10 s.
Dome shaped lens minimizes light diffusion.
LED light output matches the absorption spectrum of Camphorquinone (CQ) Photoinitiators.
Audible signal every 10 s and automatic power saving sleep mode after 20 s of operation.
Hundreds of 10-s cures with a fully charged power cell. 
Test block provided for determining accurate cure times.

 
Indications for Use
The Coltolux  LED is indicated for the polymerization of intra and extra oral restorations fabricated from materials (commonly referred to as visible light cured dental restoratives and/or composites and/or dental adhesives) that contain Camphorquinone as the photoinitiator.
 

Key Specifications
Technical Data

Handpiece wavelength range: 450 nm/470 nm
Peak wavelength range: 460 nm
Light output diameter: 9.0 mm

Dimensions

Curing probe: 0.48 (1.22 cm)diameter
 body: 1.0 (2.5 cm) diameter
length: 8.7" (22 cm) long
weight: 022 lb. (100 grams)

Charger Base Dimensions

height: 2.9" (74 cm)
width: 2.5" (6.4 cm) 
depth: 3.5" (8.9 cm)

Power Supply

input voltage: 100-240 vac

Packaging
1 x Handpiece
1 x Charger Base
1 x Power Supply
3 x Light Shields
5 x Light Lenses
100 x Barrier Sleeves

Direction of use
SET-UP AND ASSEMBLY

Remove the protective insert by first sliding the release button in the direction indicated by the arrow. Hold the button in this position while removing the insert from the supply.
Angle the top of the new adapter into the recess of the supply. Slide the release button in the direction indicated while simultaneously pressing the new adapter into place.
Insert the handpiece into the charger base. When the handpiece is being charged, the light on the charger base will be orange. When the handpiece is fully charged and ready, the orange light
on the charger base will turn green. The initial charging of the handpiece will require approximately 3 hours to fully charge.
When the handpiece is removed from the charger base the small light above the On/Off button on the handpiece will be green, indicating the unit is ready for use.

FUNCTION CHECK

Activate/Deactivate Light - Depressing the On/Off button on the handpiece activates or
deactivates the curing light. Do not hold the button continuously throughout the curing cycle. During operation an audible beep will be emitted every 10 seconds. The unit shuts off
automatically after 20 seconds.
Measuring the Light?s Effectiveness - To ensure complete polymerization at all times, it is critical to periodically test the light intensity output.
Radiometer Display - A reading of 300 mW/cm2 or higher indicates that the light output
is acceptable for the polymerization of material up to a 2.0 mm depth. Follow the dental material manufacturer?s instructions for recommended exposure time, and check using the supplied test block. A reading below 300 mW/cm2 or a reduction of intensity of the light output in comparison to the original value, indicates that corrective action should be taken.

CLINICAL APPLICATION

Polymerization: Determine the exposure time in accordance with the dental material manufacturer?s instructions using the test block provided. If the exposure time exceeds 20 sec,
COLTENE recommends including a cooldown time before initiating another cycle. Failure to do so increases the risk of tissue burns and inadvertent heating of the dental pulp.
Remove the charged handpiece from the charger base; position the light shield; slide the single use barrier sleeve over the light; attach the light shield direct the tip of the light
lens as close to the restorative material as possible without touching.
Activate Coltolux  LED with a momentary push of the button. Avoid contact with un-polymerized restorative material, glass ionomer, liquid resin or bonding agent because direct
contact will cause these materials to adhere to the light lens. This will block the light transmission and result in improper polymerization.
To safely terminate procedure, press and release activation button.

Warranty

Manufacturer/Importer warranty of 24 months as applicable for this product.
Service and Warranty are handled by the manufacturer/importer directly for this product
Divne Medicare will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer
Divne Medicare and the Buyer acknowledge that the Products purchased/usedare a subject matter of original Manufacturer/Importer?s warranties only
Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and Divne Medicare may assist the customer in registering a request to get the Product replaced or serviced. 
The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be.